通信プロトコル支援機能(GX Configurator-SC Version2.20W)でサポートしている型式(シリーズ)とコマンドの一覧です。
型式(シリーズ)でシリーズ名と型式名の併記は動作確認済みの型式です。
コマンドの詳細は、外部機器メーカのマニュアルを参照ください。
Support command < > puts the control code. |
No. | Type | Manufacturer | Model(Series) | Support Command |
Information of command |
---|---|---|---|---|---|
1 | Inverter | MITSUBISHI ELECTRIC | FREQROL Series [Confirmed model] FR-F500J FR-S500 FR-C500 FR-E500 FR-F500 FR-A500 FR-V500 FR-A700 FR-F700 FR-E700 FR-D700 |
7BH FBH 6FH 70H 74H FAH 7AH 6DH 6EH EDH EEH FDH F4H FCH - - 7FH FFH |
【Operation Mode Read】 【Operation Mode Write】 【Output Frequency/Speed Read】 【Output Current Read】 【Alarm Definition Read】 【Run Command Write】 【Inverter Status Monitor】 【Set Frequency(RAM) Read】 【Set Frequency(EEPROM) Read】 【Set Frequency(RAM) Write】 【Set Frequency(RAM, EEPROM) Write】 【Inverter Reset】 【Alarm Definition All Clear】 【All Parameter Clear】 【Parameters Read】 ・・・The command (Instruction Code:00H~63H) is specified by the program 【Parameters Write】 ・・・The command (Instruction Code:80H~E3H) is specified by the program 【Link Parameter Extended Setting Read】 【Link Parameter Extended Setting Write】 |
2 | Temperature Controller | OMRON | General-Purpose E5*N(-H) [Confirmed model] E5CN(-H) E5AN(-H) E5EN(-H) |
0101 0102 0104 0113 0503 0601 0801 3005 |
【Read Variable Area】 【Write Variable Area】 【Composite Read from Variable Area】 【Composite Write to Variable Area】 【Read Controller Attributes】 【Read Controller Status】 【Echoback Test】 【Operation Command】 |
3 | E5EK | 1 2 3 |
【Reading Parameters】 【Writing Parameters】 【Issuing Special Commands】 |
||
4 | EJ1 | 0101 0102 0104 0113 0110 0111 0112 0503 0601 0801 3005 |
【Read Variable Area】 【Write Variable Area】 【Composite Read from Variable Area】 【Composite Write to Variable Area】 【Composite Registration Read】 【Composite Read Rregistration】 【Composite Read Registration Confirmation】 【Read Controller Attributes】 【Read Controller Status】 【Echoback Test】 【Operation Command】 |
||
5 | E5ZN | 0101 0102 3005 0104 0113 0503 0601 0801 |
【Read Variable Area】 【Write Variable Area】 【Operation Command】 【Composite Read from Variable Area】 【Composite Write to Variable Area】 【Read Controller Attributes】 【Read Controller Status】 【Echoback Test】 |
||
6 | Fuji Electric Systems | PXR3 | 01H 02H 03H 04H 05H 06H 10H |
【Read-out of Bit Data】 【Read-out of Bit Data (Read-out Only)】 【Read-out of Word Data】 【Read-out of Word Data (Read-out Only)】 【Write-in of Bit Data】 【Write-in of Word Data】 【Write-in of Continuous Word Data】 |
|
7 | PXG4 | 02H 03H 04H 06H 10H |
【Read-out of Bit Data (Read-out Only)】 【Read-out of Word Data】 【Read-out of Word Data (Read-out Only)】 【Write-in of Word Data】 【Write-in of Continuous Word Data】 |
||
8 | PXH9 | 03H 04H 06H 10H |
【Read-out of Word Data】 【Read-out of Word Data (Read-out Only)】 【Write-in of Word Data】 【Write-in of Continuous Word Data】 |
||
9 | Yamatake | DMC10 | RD WD RU WU |
【Hexadecimal Format Read Command】 【Hexadecimal Format Write Command】 【Hexadecimal Format Random Read Command】 【Hexadecimal Format Random Write Command】 |
|
10 | DMC50 | RG WG RN WN |
【Read Data 32bit,Continuous (ASCII HEX)】 【Write Data 32bit,Continuous (ASCII HEX)】 【Read Data 32bit,Separate (ASCII HEX)】 【Write Data 32bit,Separate (ASCII HEX)】 |
||
11 | SDC Series [Confirmed model] SDC15 SDC25 SDC35 |
RD WD RU WU |
【Hexadecimal Format Read Command】 【Hexadecimal Format Write Command】 【Hexadecimal Format Random Read Command】 【Hexadecimal Format Random Write Command】 |
||
12 | RKC INSTRUMENT | FB400 | 03H 06H 08H 10H |
【Read Holding Registers】 【Preset Single Register】 【Diagnostics (Loopback Test)】 【Preset Multiple Registers】 |
|
13 | CB400 | - - |
【Polling】・・・The command (identifier) is specified by the program 【Selecting】・・・The command (identifier) is specified by the program |
||
14 | Barcode Reader | Datalogic | DS2***N [Confirmed model] DS2100N DS2400N |
‹ESC›[C ‹ESC›]B ‹ESC›cM ‹ESC›dM ‹ESC›IA ‹ESC›[A E P ‹STX› ‹ETX› SS 31 SS 73 SS 86 SS 87 SS 6 SS 7 |
【Enter Host Mode】 【Enter Terminal Mode】 【Enter Programming Mode】 【Exit Programming Mode】 【Exit Terminal Mode】 【Exit Host Mode】 【Data Storage (Storage in temporary and permanent memory)】 【Trigger ON】 【Trigger OFF】 【Operating Mode Selection】 【On Line Options】 【Serial Start String】 【Serial Stop String】 【Header String】 【Termination String】 |
15 | DS4800 | ||||
16 | Cognex | DataMan100 | TRIGGER - - |
【Trigger ON】 【Set】・・・The command is specified by the program 【Get】・・・The command is specified by the program |
|
17 | Actuator | IAI | CON Series [Confirmed model] PCON ACON SCON |
01H 02H 03H 04H 05H 06H 07H 0FH 10H 11H 17H |
【Read Coil Status】 【Read Input Status】 【Read Holding Registers】 【Read Input Registers】 【Force Single Coil】 【Preset Single Register】 【Read Exception Status】 【Force Multiple Coils】 【Preset Multiple Registers】 【Report Slave ID】 【Read / Write Registers】 |
18 | SEL Series [Confirmed model] PSEL ASEL SSEL |
208H 20BH 20CH 20DH 20EH 210H 212H 213H 215H 232H 24AH 24BH 24CH 24EH 252H 253H 254H 255H 256H 257H 25CH 25EH |
【Number of Effective Point Data Query】 【Input Port Query】 【Output Port Query】 【Flag Query】 【Integer Variable Query】 【String Variable Query】 【Axis Status Query】 【Program Status Query】 【System Status Query】 【Servo ON/OFF】 【Output Port Status Change】 【Flag Status Change】 【Integer Variable Change】 【String Variable Change】 【Alarm Reset】 【Program Run】 【Program End】 【Program Pause】 【Program One-Step Run】 【Program Resume】 【Drive-Source Recovery Request】 【Operation Pause Cancellation Request】 |
||
19 | ID Controller (RFID) |
OMRON | V600 | RD WT XR XW ER AR AW DF AF CP AP PR PW MD C/K MD S/L RP AA XZ TS CC CF TR SP |
【Read】 【Write】 【Expansion Read】 【Expansion Write】 【Expanded Read】 【Auto Read】 【Auto Write】 【Data Fill】 【Auto Data Fill】 【Copy】 【Auto Copy】 【Polling Auto Read】 【Polling Auto WRITE】 【Data Check】 【Overwrite Count Control】 【Write Repeat】 【Command Processing Terminate】 【Abort】 【Test】 【Controller Control】 【Read Error Information】 【Communications Conditions Setting】 【Parameter Setting】 |
20 | V680 | RD WT DF MD S/L MD C/K RP ID CP AP ER QR QW PC AA XZ US TR SP MO SE RR CC CF HI TS VS NS |
【Read】 【Write】 【Data Fill】 【Overwrite Count Control】 【Data Check】 【Write Repeat】 【Read ID】 【Copy】 【Auto Copy】 【Expanded Read】 【Read Tag Memory Error Correction】 【Write Tag Memory Error Correction】 【Polling Query】 【Command Processing Terminate】 【Abort】 【UID Addition Set】 【Communications Conditions Setting】 【Parameter Setting】 【Operation Mode Change】 【Operation Condition Set】 【Response Resend】 【Controller Control】 【Read Error Information】 【Read History Information】 【Test】 【Version Read】 【Noise Detection】 |
||
21 | B & PLUS | BIS S | R r ‹STX› W w U u S N ‹DC3› ‹DC1› |
【Read】 【Read (Wait Code Tag)】 【Start of Text】 【Write 1】 【Write 1 (Wait Code Tag)】 【Write 2】 【Write 2 (Wait Code Tag)】 【Stop Command】 【Status Request】 【Stops Sending Data】 【Restarts Sending Data】 |
|
22 | Communication Protocol | OMRON | C-mode Command | RR RL RH RC RG RD RJ RE WR WL WH WC WD WJ WE MS MF |
【CIO Area Read】 【LR Area Read】 【HR Area Read】 【Timer/Counter PV Read】 【Timer/Counter Status Read】 【DM Area Read】 【AR Area Read】 【EM Area Read】 【CIO Area Write】 【LR Area Write】 【HR Area Write】 【Timer/Counter PV Write】 【DM Area Write】 【AR Area Write】 【EM Area Write】 【Status Read】 【Error Read】 |
23 | FINS Command | 0101 0102 0103 0104 |
【Memory Area Read】 【Memory Area Write】 【Memory Area Fill】 【Multiple Memory Area Read】 |
||
24 | Schneider Electric | MODBUS | 01 02 03 04 05 06 07 08 00 08 01 08 02 08 03 08 04 08 10 08 11 08 12 08 13 08 14 08 15 08 16 08 17 08 18 11 12 15 16 17 20 21 22 23 |
【Read Coils】 【Read Discrete Inputs】 【Read Holding Registers】 【Read Input Registers】 【Write Single Coil】 【Write Single Register】 【Read Exception Status】 【Return Query Data】 【Restart Communications Option】 【Return Diagnostic Register】 【Change ASCII Input Delimiter】 【Force Listen Only Mode】 【Clear Counters and Diagnostic Register】 【Return Bus Message Count】 【Return Bus Communication Error Count】 【Return Bus Exception Error Count】 【Return Slave Message Count】 【Return Slave No Response Count】 【Return Slave NAK Count】 【Return Slave Busy Count】 【Return Bus Character Overrun Count】 【Get Communications Event Counter】 【Get Communications Event Log】 【Write Multiple Coils】 【Write Multiple Registers】 【Report Slave ID】 【Read File Record】 【Write File Record】 【Mask Write Register】 【Read/Write Multiple Registers】 |
|
25 | MITSUBISHI ELECTRIC | MC Protocol QnA Compatible 4C Frame (Format 1,4) |
0401 1401 0406 1406 |
【Batch Read】 【Batch Write】 【Multiple Block Batch Read】 【Multiple Block Batch Write】 |